Cummins fault code11398 · Add on Board Not Connected to PS0600 Control Main Hardware Board
Add on Board Not Connected to PS0600 Control Main Hardware Board - Condition Exists
11398 Cummins fault code as shown in INSITE / CaltermSPN521327 · Add on Board Not Connected to PS0600 Control Main Hardware BoardFMI31 Condition existsOBD codenone (J1939 only)LampRed STOP lampCummins textAdd on Board Not Connected to PS0600 Control Main Hardware Board - Condition ExistsFailure modeCondition ExistsWhat Cummins code 11398 means
This is not an electrical fault on a sensor. FMI 31 means the ECM has detected that the named condition for Add on Board Not Connected to PS0600 Control Main Hardware Board is true. The fault code itself is the message; the fix is to find out why the ECM believes the condition exists.
It turns on the red STOP ENGINE lamp. Cummins classes this as a fault that can damage the engine or aftertreatment if ignored: stop as soon as it is safe to do so. Many calibrations also apply an engine-protection derate while the fault is active.
On a generic J1939 scan tool, or on the dash of a Freightliner, Kenworth, Peterbilt, International or Volvo chassis, the same fault is shown as SPN 521327 FMI 31 rather than as Cummins code 11398. Cummins INSITE and Calterm show the Cummins number, the SPN / FMI pair and the lamp together.
Custom DTC delete, up to 30 codes, $150. Full DPF / EGR / SCR delete with all related codes and derates, $500. Upload your Calterm .xcal, tick the services, pay with PayPal, and the finished file comes back by email and WhatsApp.
Upload your .xcal →Cummins ECFG / E2M definitions for CM550, CM552, CM554, CM570, CM800, CM850, CM870, CM871 and more: the fault table, torque, fuelling, boost, EGR, DPF and SCR maps, ready for Calterm or WinOLS. Instant download.
Find your ECFG →Other Cummins codes on SPN 521327 Add on Board Not Connected to PS0600 Control Main Hardware Board
Code 11398 is the only Cummins fault code assigned to SPN 521327.
Related Cummins fault codes
J1939 failure mode identifiers (FMI)
FMI 31 is highlighted. The FMI is the second half of every J1939 fault and tells you how the component failed; the SPN tells you which component.
| FMI | Meaning (SAE J1939-73) |
|---|---|
| 0 | Data valid but above normal operational range - most severe level |
| 1 | Data valid but below normal operational range - most severe level |
| 2 | Data erratic, intermittent or incorrect |
| 3 | Voltage above normal, or shorted to high source |
| 4 | Voltage below normal, or shorted to low source |
| 5 | Current below normal or open circuit |
| 6 | Current above normal or grounded circuit |
| 7 | Mechanical system not responding or out of adjustment |
| 8 | Abnormal frequency, pulse width or period |
| 9 | Abnormal update rate |
| 10 | Abnormal rate of change |
| 11 | Root cause not known |
| 12 | Bad intelligent device or component |
| 13 | Out of calibration |
| 14 | Special instructions |
| 15 | Data valid but above normal operating range - least severe level |
| 16 | Data valid but above normal operating range - moderately severe level |
| 17 | Data valid but below normal operating range - least severe level |
| 18 | Data valid but below normal operating range - moderately severe level |
| 19 | Received network data in error |
| 20 | Data drifted high |
| 21 | Data drifted low |
| 22 | Reserved for SAE assignment |
| 23 | Reserved for SAE assignment |
| 24 | Reserved for SAE assignment |
| 25 | Reserved for SAE assignment |
| 26 | Reserved for SAE assignment |
| 27 | Reserved for SAE assignment |
| 28 | Reserved for SAE assignment |
| 29 | Reserved for SAE assignment |
| 30 | Reserved for SAE assignment |
| 31 | Condition exists |
Questions about code 11398
What does Cummins fault code 11398 mean?
Cummins 11398 is "Add on Board Not Connected to PS0600 Control Main Hardware Board - Condition Exists". It maps to SPN 521327 FMI 31. This is not an electrical fault on a sensor. FMI 31 means the ECM has detected that the named condition for Add on Board Not Connected to PS0600 Control Main Hardware Board is true. The fault code itself is the message; the fix is to find out why the ECM
Which lamp does fault code 11398 turn on?
Red STOP lamp: It turns on the red STOP ENGINE lamp. Cummins classes this as a fault that can damage the engine or aftertreatment if ignored: stop as soon as it is safe to do so. Many calibrations also apply an engine-protection derate while the fault is active.
How do I clear or permanently delete Cummins code 11398?
An active code goes inactive on its own once the condition is gone; the inactive record stays in the ECM fault history until it is cleared with Cummins INSITE (or a J1939 tool that supports the DM3 / DM11 clear). If the code keeps coming back because the part is gone, disconnected or not worth repairing, the lasting fix is to disable fault 11398 in the calibration: upload your .xcal to the ECFG Superstore file service, custom DTC delete from $150 (up to 30 codes), full DPF / EGR / SCR delete $500, and flash the returned file with Calterm or INSITE.
← All Cummins fault codes · XCAL file service · ECFG Superstore