Cummins fault code13328 · SUM Max Load Annual Limit Exceeded
SUM Max Load Annual Limit Exceeded - Data Valid But Above Normal Operating Range - Least Severe Level
13328 Cummins fault code as shown in INSITE / CaltermSPN516131 · SUM Max Load Annual Limit ExceededFMI15 Data valid but above normal operating range - least severe levelOBD codenone (J1939 only)LampWarning indicatorCummins textSUM Max Load Annual Limit Exceeded - Data Valid But Above Normal Operating Range - Least Severe LevelFailure modeData Valid But Above Normal Operating Range - Least Severe LevelWhat Cummins code 13328 means
The reading for SUM Max Load Annual Limit Exceeded is believed to be correct, but it has gone slightly above the normal operating range. This is the least severe of the three "above range" levels (FMI 15, 16 and 0); it is usually an early warning rather than an immediate problem.
The Cummins fault table lists it against a warning indicator rather than the red stop or amber check-engine lamp; it is an advisory that is logged and shown in INSITE.
On a generic J1939 scan tool, or on the dash of a Freightliner, Kenworth, Peterbilt, International or Volvo chassis, the same fault is shown as SPN 516131 FMI 15 rather than as Cummins code 13328. Cummins INSITE and Calterm show the Cummins number, the SPN / FMI pair and the lamp together.
Custom DTC delete, up to 30 codes, $150. Full DPF / EGR / SCR delete with all related codes and derates, $500. Upload your Calterm .xcal, tick the services, pay with PayPal, and the finished file comes back by email and WhatsApp.
Upload your .xcal →Cummins ECFG / E2M definitions for CM550, CM552, CM554, CM570, CM800, CM850, CM870, CM871 and more: the fault table, torque, fuelling, boost, EGR, DPF and SCR maps, ready for Calterm or WinOLS. Instant download.
Find your ECFG →Other Cummins codes on SPN 516131 SUM Max Load Annual Limit Exceeded
Code 13328 is the only Cummins fault code assigned to SPN 516131.
Related Cummins fault codes
J1939 failure mode identifiers (FMI)
FMI 15 is highlighted. The FMI is the second half of every J1939 fault and tells you how the component failed; the SPN tells you which component.
| FMI | Meaning (SAE J1939-73) |
|---|---|
| 0 | Data valid but above normal operational range - most severe level |
| 1 | Data valid but below normal operational range - most severe level |
| 2 | Data erratic, intermittent or incorrect |
| 3 | Voltage above normal, or shorted to high source |
| 4 | Voltage below normal, or shorted to low source |
| 5 | Current below normal or open circuit |
| 6 | Current above normal or grounded circuit |
| 7 | Mechanical system not responding or out of adjustment |
| 8 | Abnormal frequency, pulse width or period |
| 9 | Abnormal update rate |
| 10 | Abnormal rate of change |
| 11 | Root cause not known |
| 12 | Bad intelligent device or component |
| 13 | Out of calibration |
| 14 | Special instructions |
| 15 | Data valid but above normal operating range - least severe level |
| 16 | Data valid but above normal operating range - moderately severe level |
| 17 | Data valid but below normal operating range - least severe level |
| 18 | Data valid but below normal operating range - moderately severe level |
| 19 | Received network data in error |
| 20 | Data drifted high |
| 21 | Data drifted low |
| 22 | Reserved for SAE assignment |
| 23 | Reserved for SAE assignment |
| 24 | Reserved for SAE assignment |
| 25 | Reserved for SAE assignment |
| 26 | Reserved for SAE assignment |
| 27 | Reserved for SAE assignment |
| 28 | Reserved for SAE assignment |
| 29 | Reserved for SAE assignment |
| 30 | Reserved for SAE assignment |
| 31 | Condition exists |
Questions about code 13328
What does Cummins fault code 13328 mean?
Cummins 13328 is "SUM Max Load Annual Limit Exceeded - Data Valid But Above Normal Operating Range - Least Severe Level". It maps to SPN 516131 FMI 15. The reading for SUM Max Load Annual Limit Exceeded is believed to be correct, but it has gone slightly above the normal operating range. This is the least severe of the three "above range" levels (FMI 15, 16 and 0); it is usually an early warning rather than
Which lamp does fault code 13328 turn on?
Warning indicator: The Cummins fault table lists it against a warning indicator rather than the red stop or amber check-engine lamp; it is an advisory that is logged and shown in INSITE.
How do I clear or permanently delete Cummins code 13328?
An active code goes inactive on its own once the condition is gone; the inactive record stays in the ECM fault history until it is cleared with Cummins INSITE (or a J1939 tool that supports the DM3 / DM11 clear). If the code keeps coming back because the part is gone, disconnected or not worth repairing, the lasting fix is to disable fault 13328 in the calibration: upload your .xcal to the ECFG Superstore file service, custom DTC delete from $150 (up to 30 codes), full DPF / EGR / SCR delete $500, and flash the returned file with Calterm or INSITE.
← All Cummins fault codes · XCAL file service · ECFG Superstore