ECFG Superstore › Cummins fault codes › 14262

Cummins fault code14262 · Propulsion Motor 1 Control Module

Propulsion Motor 1 Control Module - Abnormal Update Rate

Fault code14262 Cummins fault code as shown in INSITE / CaltermSPN520752 · Propulsion Motor 1 Control ModuleFMI9 Abnormal update rateOBD codenone (J1939 only)LampRed STOP lampCummins textPropulsion Motor 1 Control Module - Abnormal Update RateFailure modeAbnormal Update Rate

What Cummins code 14262 means

The ECM expected Propulsion Motor 1 Control Module to arrive on the datalink at a regular rate and it is arriving late or not at all. This is a communication fault between modules (J1939 / J1587 wiring, terminating resistors, or a module that is powered down or not responding) rather than a sensor fault.

It turns on the red STOP ENGINE lamp. Cummins classes this as a fault that can damage the engine or aftertreatment if ignored: stop as soon as it is safe to do so. Many calibrations also apply an engine-protection derate while the fault is active.

On a generic J1939 scan tool, or on the dash of a Freightliner, Kenworth, Peterbilt, International or Volvo chassis, the same fault is shown as SPN 520752 FMI 9 rather than as Cummins code 14262. Cummins INSITE and Calterm show the Cummins number, the SPN / FMI pair and the lamp together.

Fix the file: delete code 14262 from your calibration
from $150

Custom DTC delete, up to 30 codes, $150. Full DPF / EGR / SCR delete with all related codes and derates, $500. Upload your Calterm .xcal, tick the services, pay with PayPal, and the finished file comes back by email and WhatsApp.

Upload your .xcal →
ECFG definition files for your ECM
1,800 files

Cummins ECFG / E2M definitions for CM550, CM552, CM554, CM570, CM800, CM850, CM870, CM871 and more: the fault table, torque, fuelling, boost, EGR, DPF and SCR maps, ready for Calterm or WinOLS. Instant download.

Find your ECFG →

Other Cummins codes on SPN 520752 Propulsion Motor 1 Control Module

2 other fault codes share this SPN; each one is a different failure mode (FMI) of the same component.

4963 FMI 3114263 FMI 13

All codes grouped by SPN →

Related Cummins fault codes

14257 · SPN 520750 FMI 3High Voltage Active Discharge driver14258 · SPN 520750 FMI 4High Voltage Active Discharge driver14259 · SPN 520751 FMI 20Propulsion Motor 114261 · SPN 520751 FMI 21Propulsion Motor 114263 · SPN 520752 FMI 13Propulsion Motor 1 Control Module14264 · SPN 520751 FMI 3Propulsion Motor 114265 · SPN 520753 FMI 18Low SOC Error14266 · SPN 520753 FMI 1Low SOC Error

J1939 failure mode identifiers (FMI)

FMI 9 is highlighted. The FMI is the second half of every J1939 fault and tells you how the component failed; the SPN tells you which component.

FMIMeaning (SAE J1939-73)
0Data valid but above normal operational range - most severe level
1Data valid but below normal operational range - most severe level
2Data erratic, intermittent or incorrect
3Voltage above normal, or shorted to high source
4Voltage below normal, or shorted to low source
5Current below normal or open circuit
6Current above normal or grounded circuit
7Mechanical system not responding or out of adjustment
8Abnormal frequency, pulse width or period
9Abnormal update rate
10Abnormal rate of change
11Root cause not known
12Bad intelligent device or component
13Out of calibration
14Special instructions
15Data valid but above normal operating range - least severe level
16Data valid but above normal operating range - moderately severe level
17Data valid but below normal operating range - least severe level
18Data valid but below normal operating range - moderately severe level
19Received network data in error
20Data drifted high
21Data drifted low
22Reserved for SAE assignment
23Reserved for SAE assignment
24Reserved for SAE assignment
25Reserved for SAE assignment
26Reserved for SAE assignment
27Reserved for SAE assignment
28Reserved for SAE assignment
29Reserved for SAE assignment
30Reserved for SAE assignment
31Condition exists

Questions about code 14262

What does Cummins fault code 14262 mean?

Cummins 14262 is "Propulsion Motor 1 Control Module - Abnormal Update Rate". It maps to SPN 520752 FMI 9. The ECM expected Propulsion Motor 1 Control Module to arrive on the datalink at a regular rate and it is arriving late or not at all. This is a communication fault between modules (J1939 / J1587 wiring, terminating resistors, or a module that is powered down

Which lamp does fault code 14262 turn on?

Red STOP lamp: It turns on the red STOP ENGINE lamp. Cummins classes this as a fault that can damage the engine or aftertreatment if ignored: stop as soon as it is safe to do so. Many calibrations also apply an engine-protection derate while the fault is active.

How do I clear or permanently delete Cummins code 14262?

An active code goes inactive on its own once the condition is gone; the inactive record stays in the ECM fault history until it is cleared with Cummins INSITE (or a J1939 tool that supports the DM3 / DM11 clear). If the code keeps coming back because the part is gone, disconnected or not worth repairing, the lasting fix is to disable fault 14262 in the calibration: upload your .xcal to the ECFG Superstore file service, custom DTC delete from $150 (up to 30 codes), full DPF / EGR / SCR delete $500, and flash the returned file with Calterm or INSITE.

← All Cummins fault codes  ·  XCAL file service  ·  ECFG Superstore