ECFG Superstore › Cummins fault codes › 14778

Cummins fault code14778 · Fuel Cell Stack Hydrogen Concentration

Fuel Cell Stack Hydrogen Concentration - Data Valid But Above Normal Operating Range - Most Severe Level

Fault code14778 Cummins fault code as shown in INSITE / CaltermSPN517110 · Fuel Cell Stack Hydrogen ConcentrationFMI0 Data valid but above normal operational range - most severe levelOBD codenone (J1939 only)LampRed STOP lampCummins textFuel Cell Stack Hydrogen Concentration - Data Valid But Above Normal Operating Range - Most Severe LevelFailure modeData Valid But Above Normal Operating Range - Most Severe Level

What Cummins code 14778 means

The reading for Fuel Cell Stack Hydrogen Concentration is believed to be correct, but it has gone above the highest limit in the calibration. This is the most severe of the three "above range" levels (FMI 15, 16 and 0), so the ECM is reporting a real operating problem rather than a wiring fault.

It turns on the red STOP ENGINE lamp. Cummins classes this as a fault that can damage the engine or aftertreatment if ignored: stop as soon as it is safe to do so. Many calibrations also apply an engine-protection derate while the fault is active.

On a generic J1939 scan tool, or on the dash of a Freightliner, Kenworth, Peterbilt, International or Volvo chassis, the same fault is shown as SPN 517110 FMI 0 rather than as Cummins code 14778. Cummins INSITE and Calterm show the Cummins number, the SPN / FMI pair and the lamp together.

Fix the file: delete code 14778 from your calibration
from $150

Custom DTC delete, up to 30 codes, $150. Full DPF / EGR / SCR delete with all related codes and derates, $500. Upload your Calterm .xcal, tick the services, pay with PayPal, and the finished file comes back by email and WhatsApp.

Upload your .xcal →
ECFG definition files for your ECM
1,800 files

Cummins ECFG / E2M definitions for CM550, CM552, CM554, CM570, CM800, CM850, CM870, CM871 and more: the fault table, torque, fuelling, boost, EGR, DPF and SCR maps, ready for Calterm or WinOLS. Instant download.

Find your ECFG →

Other Cummins codes on SPN 517110 Fuel Cell Stack Hydrogen Concentration

2 other fault codes share this SPN; each one is a different failure mode (FMI) of the same component.

14978 FMI 1516141 FMI 16

All codes grouped by SPN →

Related Cummins fault codes

14774 · SPN 517109 FMI 7High Voltage Output Contactor14775 · SPN 517109 FMI 31High Voltage Output Contactor14776 · SPN 517019 FMI 0Fuel Cell DC/DC Converter Output Voltage14777 · SPN 517019 FMI 1Fuel Cell DC/DC Converter Output Voltage14779 · SPN 517111 FMI 0Hydrogen Supply Pressure14781 · SPN 517111 FMI 1Hydrogen Supply Pressure14782 · SPN 517119 FMI 1Fuel Cell Stack High Voltage Insulation14783 · SPN 517120 FMI 0Stack Hydrogen/Air Crossover Pressure

J1939 failure mode identifiers (FMI)

FMI 0 is highlighted. The FMI is the second half of every J1939 fault and tells you how the component failed; the SPN tells you which component.

FMIMeaning (SAE J1939-73)
0Data valid but above normal operational range - most severe level
1Data valid but below normal operational range - most severe level
2Data erratic, intermittent or incorrect
3Voltage above normal, or shorted to high source
4Voltage below normal, or shorted to low source
5Current below normal or open circuit
6Current above normal or grounded circuit
7Mechanical system not responding or out of adjustment
8Abnormal frequency, pulse width or period
9Abnormal update rate
10Abnormal rate of change
11Root cause not known
12Bad intelligent device or component
13Out of calibration
14Special instructions
15Data valid but above normal operating range - least severe level
16Data valid but above normal operating range - moderately severe level
17Data valid but below normal operating range - least severe level
18Data valid but below normal operating range - moderately severe level
19Received network data in error
20Data drifted high
21Data drifted low
22Reserved for SAE assignment
23Reserved for SAE assignment
24Reserved for SAE assignment
25Reserved for SAE assignment
26Reserved for SAE assignment
27Reserved for SAE assignment
28Reserved for SAE assignment
29Reserved for SAE assignment
30Reserved for SAE assignment
31Condition exists

Questions about code 14778

What does Cummins fault code 14778 mean?

Cummins 14778 is "Fuel Cell Stack Hydrogen Concentration - Data Valid But Above Normal Operating Range - Most Severe Level". It maps to SPN 517110 FMI 0. The reading for Fuel Cell Stack Hydrogen Concentration is believed to be correct, but it has gone above the highest limit in the calibration. This is the most severe of the three "above range" levels (FMI 15, 16 and 0), so the ECM is reporting a real operating

Which lamp does fault code 14778 turn on?

Red STOP lamp: It turns on the red STOP ENGINE lamp. Cummins classes this as a fault that can damage the engine or aftertreatment if ignored: stop as soon as it is safe to do so. Many calibrations also apply an engine-protection derate while the fault is active.

How do I clear or permanently delete Cummins code 14778?

An active code goes inactive on its own once the condition is gone; the inactive record stays in the ECM fault history until it is cleared with Cummins INSITE (or a J1939 tool that supports the DM3 / DM11 clear). If the code keeps coming back because the part is gone, disconnected or not worth repairing, the lasting fix is to disable fault 14778 in the calibration: upload your .xcal to the ECFG Superstore file service, custom DTC delete from $150 (up to 30 codes), full DPF / EGR / SCR delete $500, and flash the returned file with Calterm or INSITE.

← All Cummins fault codes  ·  XCAL file service  ·  ECFG Superstore