Cummins fault code16352 · Engine Cylinder 1 Ignition Transformer Secondary Output
Engine Cylinder 1 Ignition Transformer Secondary Output - Mechanical System Not Responding or Out of Adjustment
16352 Cummins fault code as shown in INSITE / CaltermSPN1393 · Engine Cylinder 1 Ignition Transformer Secondary OutputFMI7 Mechanical system not responding or out of adjustmentOBD codeP2302LampAmber WARNING lampCummins textEngine Cylinder 1 Ignition Transformer Secondary Output - Mechanical System Not Responding or Out of AdjustmentFailure modeMechanical System Not Responding or Out of AdjustmentWhat Cummins code 16352 means
The electrical side of Engine Cylinder 1 Ignition Transformer Secondary Output checks out, but the mechanical part is not doing what the ECM commanded or is out of its adjustment range. Think stuck valves, seized actuators, worn linkages, or a part that moves but never reaches the commanded position.
It lights the amber CHECK ENGINE (warning) lamp. The engine keeps running, but a torque or speed derate may apply depending on the calibration and on how long the fault stays active.
On a generic J1939 scan tool, or on the dash of a Freightliner, Kenworth, Peterbilt, International or Volvo chassis, the same fault is shown as SPN 1393 FMI 7 rather than as Cummins code 16352; an OBD-II reader shows it as P2302. Cummins INSITE and Calterm show the Cummins number, the SPN / FMI pair and the lamp together.
Custom DTC delete, up to 30 codes, $150. Full DPF / EGR / SCR delete with all related codes and derates, $500. Upload your Calterm .xcal, tick the services, pay with PayPal, and the finished file comes back by email and WhatsApp.
Upload your .xcal →Cummins ECFG / E2M definitions for CM550, CM552, CM554, CM570, CM800, CM850, CM870, CM871 and more: the fault table, torque, fuelling, boost, EGR, DPF and SCR maps, ready for Calterm or WinOLS. Instant download.
Find your ECFG →Other Cummins codes on SPN 1393 Engine Cylinder 1 Ignition Transformer Secondary Output
4 other fault codes share this SPN; each one is a different failure mode (FMI) of the same component.
Related Cummins fault codes
J1939 failure mode identifiers (FMI)
FMI 7 is highlighted. The FMI is the second half of every J1939 fault and tells you how the component failed; the SPN tells you which component.
| FMI | Meaning (SAE J1939-73) |
|---|---|
| 0 | Data valid but above normal operational range - most severe level |
| 1 | Data valid but below normal operational range - most severe level |
| 2 | Data erratic, intermittent or incorrect |
| 3 | Voltage above normal, or shorted to high source |
| 4 | Voltage below normal, or shorted to low source |
| 5 | Current below normal or open circuit |
| 6 | Current above normal or grounded circuit |
| 7 | Mechanical system not responding or out of adjustment |
| 8 | Abnormal frequency, pulse width or period |
| 9 | Abnormal update rate |
| 10 | Abnormal rate of change |
| 11 | Root cause not known |
| 12 | Bad intelligent device or component |
| 13 | Out of calibration |
| 14 | Special instructions |
| 15 | Data valid but above normal operating range - least severe level |
| 16 | Data valid but above normal operating range - moderately severe level |
| 17 | Data valid but below normal operating range - least severe level |
| 18 | Data valid but below normal operating range - moderately severe level |
| 19 | Received network data in error |
| 20 | Data drifted high |
| 21 | Data drifted low |
| 22 | Reserved for SAE assignment |
| 23 | Reserved for SAE assignment |
| 24 | Reserved for SAE assignment |
| 25 | Reserved for SAE assignment |
| 26 | Reserved for SAE assignment |
| 27 | Reserved for SAE assignment |
| 28 | Reserved for SAE assignment |
| 29 | Reserved for SAE assignment |
| 30 | Reserved for SAE assignment |
| 31 | Condition exists |
Questions about code 16352
What does Cummins fault code 16352 mean?
Cummins 16352 is "Engine Cylinder 1 Ignition Transformer Secondary Output - Mechanical System Not Responding or Out of Adjustment". It maps to SPN 1393 FMI 7 and OBD code P2302. The electrical side of Engine Cylinder 1 Ignition Transformer Secondary Output checks out, but the mechanical part is not doing what the ECM commanded or is out of its adjustment range. Think stuck valves, seized actuators, worn linkages, or a part that moves
Which lamp does fault code 16352 turn on?
Amber WARNING lamp: It lights the amber CHECK ENGINE (warning) lamp. The engine keeps running, but a torque or speed derate may apply depending on the calibration and on how long the fault stays active.
How do I clear or permanently delete Cummins code 16352?
An active code goes inactive on its own once the condition is gone; the inactive record stays in the ECM fault history until it is cleared with Cummins INSITE (or a J1939 tool that supports the DM3 / DM11 clear). If the code keeps coming back because the part is gone, disconnected or not worth repairing, the lasting fix is to disable fault 16352 in the calibration: upload your .xcal to the ECFG Superstore file service, custom DTC delete from $150 (up to 30 codes), full DPF / EGR / SCR delete $500, and flash the returned file with Calterm or INSITE.
← All Cummins fault codes · XCAL file service · ECFG Superstore