Cummins fault code1663 · Aftertreatment Exhaust Gas Temperature 1 Swapped
Aftertreatment Exhaust Gas Temperature 1 Swapped - Out of Calibration
1663 Cummins fault code as shown in INSITE / CaltermSPN3241 · Aftertreatment Exhaust Gas Temperature 1FMI13 Out of calibrationOBD codeP141ALampAmber WARNING lampCummins textAftertreatment Exhaust Gas Temperature 1 Swapped - Out of CalibrationFailure modeOut of CalibrationWhat Cummins code 1663 means
The calibration data stored for Aftertreatment Exhaust Gas Temperature 1 Swapped does not match what the ECM measures or expects. This can be an adaptive value that has drifted outside limits, a component that was replaced without the matching learn procedure, or calibration data that is missing or corrupt.
It lights the amber CHECK ENGINE (warning) lamp. The engine keeps running, but a torque or speed derate may apply depending on the calibration and on how long the fault stays active.
On a generic J1939 scan tool, or on the dash of a Freightliner, Kenworth, Peterbilt, International or Volvo chassis, the same fault is shown as SPN 3241 FMI 13 rather than as Cummins code 1663; an OBD-II reader shows it as P141A. Cummins INSITE and Calterm show the Cummins number, the SPN / FMI pair and the lamp together.
This is an emissions-system code. If the component it refers to has been removed or unplugged (DPF, EGR, SCR / DEF or NOx sensor delete) the code will keep returning and the derate with it, however many times it is cleared, because the diagnostic is still enabled in the calibration. The lasting fix in that case is to disable the fault in the .xcal itself.
Custom DTC delete, up to 30 codes, $150. Full DPF / EGR / SCR delete with all related codes and derates, $500. Upload your Calterm .xcal, tick the services, pay with PayPal, and the finished file comes back by email and WhatsApp.
Upload your .xcal →Cummins ECFG / E2M definitions for CM550, CM552, CM554, CM570, CM800, CM850, CM870, CM871 and more: the fault table, torque, fuelling, boost, EGR, DPF and SCR maps, ready for Calterm or WinOLS. Instant download.
Find your ECFG →Other Cummins codes on SPN 3241 Aftertreatment Exhaust Gas Temperature 1
8 other fault codes share this SPN; each one is a different failure mode (FMI) of the same component.
Related Cummins fault codes
J1939 failure mode identifiers (FMI)
FMI 13 is highlighted. The FMI is the second half of every J1939 fault and tells you how the component failed; the SPN tells you which component.
| FMI | Meaning (SAE J1939-73) |
|---|---|
| 0 | Data valid but above normal operational range - most severe level |
| 1 | Data valid but below normal operational range - most severe level |
| 2 | Data erratic, intermittent or incorrect |
| 3 | Voltage above normal, or shorted to high source |
| 4 | Voltage below normal, or shorted to low source |
| 5 | Current below normal or open circuit |
| 6 | Current above normal or grounded circuit |
| 7 | Mechanical system not responding or out of adjustment |
| 8 | Abnormal frequency, pulse width or period |
| 9 | Abnormal update rate |
| 10 | Abnormal rate of change |
| 11 | Root cause not known |
| 12 | Bad intelligent device or component |
| 13 | Out of calibration |
| 14 | Special instructions |
| 15 | Data valid but above normal operating range - least severe level |
| 16 | Data valid but above normal operating range - moderately severe level |
| 17 | Data valid but below normal operating range - least severe level |
| 18 | Data valid but below normal operating range - moderately severe level |
| 19 | Received network data in error |
| 20 | Data drifted high |
| 21 | Data drifted low |
| 22 | Reserved for SAE assignment |
| 23 | Reserved for SAE assignment |
| 24 | Reserved for SAE assignment |
| 25 | Reserved for SAE assignment |
| 26 | Reserved for SAE assignment |
| 27 | Reserved for SAE assignment |
| 28 | Reserved for SAE assignment |
| 29 | Reserved for SAE assignment |
| 30 | Reserved for SAE assignment |
| 31 | Condition exists |
Questions about code 1663
What does Cummins fault code 1663 mean?
Cummins 1663 is "Aftertreatment Exhaust Gas Temperature 1 Swapped - Out of Calibration". It maps to SPN 3241 FMI 13 and OBD code P141A. The calibration data stored for Aftertreatment Exhaust Gas Temperature 1 Swapped does not match what the ECM measures or expects. This can be an adaptive value that has drifted outside limits, a component that was replaced without the matching learn procedure
Which lamp does fault code 1663 turn on?
Amber WARNING lamp: It lights the amber CHECK ENGINE (warning) lamp. The engine keeps running, but a torque or speed derate may apply depending on the calibration and on how long the fault stays active.
How do I clear or permanently delete Cummins code 1663?
An active code goes inactive on its own once the condition is gone; the inactive record stays in the ECM fault history until it is cleared with Cummins INSITE (or a J1939 tool that supports the DM3 / DM11 clear). If the code keeps coming back because the part is gone, disconnected or not worth repairing, the lasting fix is to disable fault 1663 in the calibration: upload your .xcal to the ECFG Superstore file service, custom DTC delete from $150 (up to 30 codes), full DPF / EGR / SCR delete $500, and flash the returned file with Calterm or INSITE.
← All Cummins fault codes · XCAL file service · ECFG Superstore