ECFG Superstore › Cummins fault codes › 7879

Cummins fault code7879 · Aftertreatment 1 Diesel Oxidation Catalyst System

Aftertreatment 1 Diesel Oxidation Catalyst System - Condition Exists

Fault code7879 Cummins fault code as shown in INSITE / CaltermSPN5018 · Aftertreatment 1 Diesel Oxidation Catalyst SystemFMI31 Condition existsOBD codenone (J1939 only)LampNo lampCummins textAftertreatment 1 Diesel Oxidation Catalyst System - Condition ExistsFailure modeCondition Exists

What Cummins code 7879 means

This is not an electrical fault on a sensor. FMI 31 means the ECM has detected that the named condition for Aftertreatment 1 Diesel Oxidation Catalyst System is true. The fault code itself is the message; the fix is to find out why the ECM believes the condition exists.

No dash lamp is attached to this code in the Cummins fault table. It is logged in the ECM and shows up in Cummins INSITE (or any J1939 tool reading DM1 / DM2), but on its own it does not light a lamp.

On a generic J1939 scan tool, or on the dash of a Freightliner, Kenworth, Peterbilt, International or Volvo chassis, the same fault is shown as SPN 5018 FMI 31 rather than as Cummins code 7879. Cummins INSITE and Calterm show the Cummins number, the SPN / FMI pair and the lamp together.

This is an emissions-system code. If the component it refers to has been removed or unplugged (DPF, EGR, SCR / DEF or NOx sensor delete) the code will keep returning and the derate with it, however many times it is cleared, because the diagnostic is still enabled in the calibration. The lasting fix in that case is to disable the fault in the .xcal itself.

Fault code 7879 is defined in the fault tables of the Cummins calibrations we have analysed, so it is a real, current code rather than a legacy number.

Fix the file: delete code 7879 from your calibration
from $150

Custom DTC delete, up to 30 codes, $150. Full DPF / EGR / SCR delete with all related codes and derates, $500. Upload your Calterm .xcal, tick the services, pay with PayPal, and the finished file comes back by email and WhatsApp.

Upload your .xcal →
ECFG definition files for your ECM
1,800 files

Cummins ECFG / E2M definitions for CM550, CM552, CM554, CM570, CM800, CM850, CM870, CM871 and more: the fault table, torque, fuelling, boost, EGR, DPF and SCR maps, ready for Calterm or WinOLS. Instant download.

Find your ECFG →

Other Cummins codes on SPN 5018 Aftertreatment 1 Diesel Oxidation Catalyst System

4 other fault codes share this SPN; each one is a different failure mode (FMI) of the same component.

1994 FMI 112637 FMI 114214 FMI 185617 FMI 14

All codes grouped by SPN →

Related Cummins fault codes

7875 · SPN 521185 FMI 18Fuel Pump 2 Remaining Useful Life7876 · SPN 521185 FMI 18Fuel Pump 2 Remaining Useful Life7877 · SPN 521185 FMI 17Fuel Pump 2 Remaining Useful Life7878 · SPN 521185 FMI 17Fuel Pump 2 Remaining Useful Life7881 · SPN 4411 FMI 16Aftertreatment 2 SCR Differential Pressure7882 · SPN 4411 FMI 0Aftertreatment 2 SCR Differential Pressure7883 · SPN 4411 FMI 3Aftertreatment 2 SCR Differential Pressure7884 · SPN 4411 FMI 4Aftertreatment 2 SCR Differential Pressure

J1939 failure mode identifiers (FMI)

FMI 31 is highlighted. The FMI is the second half of every J1939 fault and tells you how the component failed; the SPN tells you which component.

FMIMeaning (SAE J1939-73)
0Data valid but above normal operational range - most severe level
1Data valid but below normal operational range - most severe level
2Data erratic, intermittent or incorrect
3Voltage above normal, or shorted to high source
4Voltage below normal, or shorted to low source
5Current below normal or open circuit
6Current above normal or grounded circuit
7Mechanical system not responding or out of adjustment
8Abnormal frequency, pulse width or period
9Abnormal update rate
10Abnormal rate of change
11Root cause not known
12Bad intelligent device or component
13Out of calibration
14Special instructions
15Data valid but above normal operating range - least severe level
16Data valid but above normal operating range - moderately severe level
17Data valid but below normal operating range - least severe level
18Data valid but below normal operating range - moderately severe level
19Received network data in error
20Data drifted high
21Data drifted low
22Reserved for SAE assignment
23Reserved for SAE assignment
24Reserved for SAE assignment
25Reserved for SAE assignment
26Reserved for SAE assignment
27Reserved for SAE assignment
28Reserved for SAE assignment
29Reserved for SAE assignment
30Reserved for SAE assignment
31Condition exists

Questions about code 7879

What does Cummins fault code 7879 mean?

Cummins 7879 is "Aftertreatment 1 Diesel Oxidation Catalyst System - Condition Exists". It maps to SPN 5018 FMI 31. This is not an electrical fault on a sensor. FMI 31 means the ECM has detected that the named condition for Aftertreatment 1 Diesel Oxidation Catalyst System is true. The fault code itself is the message; the fix is to find out why the ECM believes the

Which lamp does fault code 7879 turn on?

No lamp: No dash lamp is attached to this code in the Cummins fault table. It is logged in the ECM and shows up in Cummins INSITE (or any J1939 tool reading DM1 / DM2), but on its own it does not light a lamp.

How do I clear or permanently delete Cummins code 7879?

An active code goes inactive on its own once the condition is gone; the inactive record stays in the ECM fault history until it is cleared with Cummins INSITE (or a J1939 tool that supports the DM3 / DM11 clear). If the code keeps coming back because the part is gone, disconnected or not worth repairing, the lasting fix is to disable fault 7879 in the calibration: upload your .xcal to the ECFG Superstore file service, custom DTC delete from $150 (up to 30 codes), full DPF / EGR / SCR delete $500, and flash the returned file with Calterm or INSITE.

← All Cummins fault codes  ·  XCAL file service  ·  ECFG Superstore